Dc Gear Motor, namely Gear Reduction Motor, is based on ordinary Dc Motor , coupled with gear reduction gearbox.
The gear reducer is used to provide low speed and large torque.
At the same time, the gearbox with different deceleration ratio can provide different speed and torque.
Generally different industries, using different power dc motor, generally adopt custom parameter design pattern.
What are the four ratings of the Dc Gear Motor? The DC gear motor is often seen in our industrial production. Here Shunchang Motor gives you the knowledge of its four ratings. To talk about
precision instruments and meters,automobile industry, medical equipment, consumer electronics, household appliances, electric glass doors and Windows,etc., wide application range
Features: gear motor drive precision, small volume, large torque, low noise, durability, low energy consumption, customized power design,easy installation, easy maintenance;Simplify design and save space.
Method of use: the best stable in horizontal plane, installed on the dc gear motor output shaft parts, cannot use a hammer to knock,knock prone to press into the dc gear motor drive, may cause damage to internal components, and cannot be used in the case of blocked.
Operating temperature range:
Geared motors should be used at a temperature of -10~60℃.
The figures stated in the catalog specifications are based on use at ordinary room temperature catalog specifications re based on use at ordinary room temperature (approximately20~25℃.
If a geared motor is used outside the prescribed temperature range,the grease on the gearhead area will become unable to function normally and the motor will become unable to start.Depending on the temperature conditions ,it may be possible to deal with them by changing the grease of the motor's parts.Please feel free to consult with us about this.
Storage temperature range:
Geared motors should be stored ta a temperature of -15~65℃.
In case of storage outside this range,the grease on the gearhead area will become unable to function normally and the motor will become unable to start.
Service life:
â—Use with a load that exceeds the rated torque
â—Frequent starting
â—Momentary reversals of turning direction
â—Impact loads
â—Long-term continuous operation
â—Forced turning using the output shaft
â—Use in which the permitted overhang load or the permitted thrust load is exceeded
â—A pulse drive ,e.g.,a short break,counter electromotive force,PWM control
â—Use of a voltage that is nonstandard as regards the rated voltage
â—Use outside the prescribed temperature or relative-humidity range,or in a special environment.
â—Please consult with us about these or any other conditions of use that may apply,so that we can be sure that you select the most appropriate model.
when it come to volume production,we're a major player as well .each month,we rurn out 600000 units,all of which are compliant with the rohs directive.Have any questions or special needed, please contact us, we have the engineer group and best sales department to service to you Looking forward to your inquiry. Welcome to our factory.
Gear Motor Gear Motor,Micro Gear Motor,Small Gear Motor,Bike Lock Gear Motor Shenzhen Shunchang Motor Co., LTD. , https://www.scgearmotor.com
Earlier, NVC dealers told reporters that the new brand would force Wu Changjiang to preside over the overall situation and had already invited many NVC executives. However, Wu Changjiang said that he had already telephoned with major NVC executives to prevent them from participating in the new brand. "They are still in NVC now, of course they can't manage other brands. This is legally responsible. Will pass."
Wu Changjiang said that the dealer's mood can be understood, but he does not want to use excessive behavior to solve the problem. "I and the dealers have said that I am the founder and major shareholder. It is a matter of time to come back, as long as I put it Good performance, who doesn't believe me?"
However, Wu Changjiang also revealed that some dealers are very determined, which makes the situation difficult to control. "I don't know who they are planning behind. I also know that they will discuss the new company in Zhongshan today (July 27). But I won't go there."
Wu Changjiang said that the current communication between He and Schneider Zhuhai is relatively smooth. Everyone hopes that the company can resume operations as soon as possible and seize the opportunity of the sales season in the second half of the year to make up for the negative impact of the strike.
Wu Changjiang stressed that there is no big contradiction between the peace and harmony. They also called this morning, but Wu Changjiang did not want to disclose the details of the specific negotiations. Regarding whether he can return to the board of directors in the near future, Wu Changjiang said that this was the decision of the board of directors. He did not participate in the board meeting for the past two days, so he did not know.
The person dialed the phone number, but he said that he could not disclose the specific content of the board meeting and would tell everyone at the appropriate time according to the requirements of the listed company. An insider of NVC told reporters that the board of directors has not yet reached an agreement.
It is understood that NVC dealers will meet in Zhongshan today to discuss the establishment of a new company. Previously, the dealer alliance has planned to invest 10 million yuan per dealer and raise more than 3 billion yuan to operate the new brand. It is imperative to start a new stove. The “Great NVC†system, including suppliers and distributors, is facing the risk of collapse.
"This is also the situation I am most worried about at the moment." Wu Changjiang said, "The advantage of NVC is in the channel. Now the channel has to set up a new brand. The situation is indeed very critical, but I still hope to think about it, I will continue. Convince them."
"I know that dealers have opinions on the employers, but I don't want everyone to be angry. Who is angry is irresponsible to the minority shareholders. I also think that everyone has some misunderstandings about me and that I am a grasshopper. In fact, I am still quite rational. People, if I don't follow the rules, I can't do it today. I still hope that things can be solved rationally. I hope everyone will resume work as soon as possible."
Wu Changjiang revealed that he went to Hong Kong yesterday, and today he is in Shenzhen. He plans to fly back to Chongqing on the weekend to deal with related matters. 
1. Rated Current: The rated current is the maximum current allowed to flow through the armature winding of the DC deceleration motor in accordance with the specified operating mode, in A.
2. Rated Voltage: The rated voltage is the maximum additional voltage that the armature winding of the motor can work safely, unit V. It
3. Rated Speed: Rated speed refers to the rotational speed of the Gear Reducer Motor in the rated voltage, rated current and output rated power under the circumstances of operation, the unit is r/min. Such
4, rated power: rated power refers to the motor in accordance with the specified mode of operation can provide output power. For motor, rated power is the output of mechanical power on the shaft.
Wu Changjiang: Resisting dealers to rebuild new brands
On July 27, when NVC dealers wanted to set up a new company and the board of directors was unable to communicate slowly, NVC lighting founder Wu Changjiang accepted a telephone interview. He said that he would try his best to convince the dealers not to set up a new brand. Let NVC operate well. "If they must, I will never participate in the management of the new brand."